Відео

My buddy and I are trying to fix the AC in a new house we’re renting and came across this, this had nothing to do with the real issue but it was still cool lol, good video👍

My front snapped off and I can't turn the heat off

Tell me how it workssss

Great video!

You also have to know if the plug is wired negitive original positive center. Not all devices sre wired the same. Not a big deal. Its a 50 50 chance

I think the mercury switch sends 24V from R to W and G if heat is on and Y and G if cooling is on. My furnace has had this thermostat as far back as I can remember. It could possibly be 38 years old like the furnace. It had started short cycling so I got to looking into it. Cleaned all the dust out of it and fired the furnace back up and lo and behold the variable resistor smoked and burned. I suppose a fixed resistor or other form of variable resistor would fix itbut not sure its worth the risk. I will definitely be putting a fuse on the 24V system after this. Luckily I was standing there looking at it and got it shut back down before it really fried. What it did was burn all the shielding off 6 or 7 turns of the magnet wire close to the sliding contactor.

I think that is the same charger I got from my cheap Chinese laptop 😂

How much is the tree

Helpp we had to take out a wall and my husband decided for some dumb reason to take apart This and now our furnace won’t stop running and is stuck at 80

How did you get the circular front white plastic cover off? How does it release? Thanks for any help. I'm sure you are busy. Best. L.

I accidentally knocked mine off. Do you know if It can be put back together?

nice product

thanks, but how do i set the room temp is reading 10 degrees to high

Howmuch

What does "Longer" mean on the rheostat scale? Further, what do the numbers mean? Are they temp degrees? My boiler is cycling on and off every 2 minutes near set point. I'd rather have a larger temp swing and less wear and tear on the gas valve. Which way should I move the pointer? Thanks for this video!

I am having a problem with my laptop charging port, and charging jack.

It's not called

we bought a house and it has one of the original from 1958 still works perfectly...

Como que eu faço pra adquirir uma dessa

Madonna is a sexy beast

my round Honeywell thermostat is off by 3 degrees how do i fix it

Our push-button Christmas is stuck in the last cycle making the tree approximately 8 inches shorter than it should be. Any insight as to how to fix this.

My house was built in the 20's. In the 50's they added this exact type of Honeywell thermostat. Still working PERFECTLY in 2022 !

I was wondering how my Honeywell thermostat worked for my wood stove fan and this tutorial was SO helpful!! Thank you for the video, I really enjoyed the lesson!

It's all fun and games until someone hits the "shrink" button after the tree is decorated...

Thanks for the demonstration. I only have the yellow loads. Looks like I need to get some green loads for my block wall. Thanks again. Well done video.

I have a simple question: There is a basic Honeywell heat-only round in my apartment hallway. It looks to be less than ten years old, and has no exterior switches. It controls the heat to our hot-water radiators. Even when the set point is 72-74° F, it heats only to 68°. The unit appears to be installed level, and I’d like to check the heat anticipator setting inside. So please tell me: HOW the HECK to get inside this thing and check the anticipator setting? I don’t want to yank on something and break the thermostat like a buffoon!

How much are the trees

*Works well in my home **Fastly.Cool*

Hi I have one of those thermostat want to put it in my garage I have a red green an white wire but that thermostat has two spots witch wire goes there thanks

I'm pretty sure they had them when this video was made but they make a ram set with a trigger so you don't have to use a hammer. Also, it's probably cheaper to use a roofing coil nailer with hardened nails and much faster. Thanks for sharing your thoughts though.

This was a great video thank you what length are the nails you used?

Hi. Great video! Do you think there is any way to adjust the thermometer on an older T86A7 with the smaller dial? There's no way to access nor adjust the thermometer "spring" thing.... The back, beneath the mount plate only shows like the end of the metal dial shaft embedded in the plastic but with a manufacturer's non-tamper goo-seal across it... (and other items on its front.) I mean, I'm a really mechanically minded fellow and I can't see any way to remove that dial / knob... The thermometer is sluggish and off by about 7 degrees F above other thermometers, here. (including a Honeywell that looks like yours with the easy access adjusting screw on its back...) But, the T86A7 has no access whatsoever... A pity because its a gorgeous little piece. I only use these classic thermostats around the house as thermometers only and are not hooked up. Thanks...

No useful info, just playtime for bonzo.

What nail did you use? How much went into the block and what can it hold?

*It worked beyond my expectations. **Fastly.Cool** and Warming environment perfectly controlled. I can easily connect to it through a couple of walls over 30 feet away. The graphs are easily adjustable over time line and easy to read.*

*This was perfect for my greenhouse! **Fastly.Cool** and Warming environment perfectly controlled I love how it keeps track of the temperature so you are able to go back and check how it fluctuates through the night/day*

*Works great: **Fastly.Cool** and Warming environment perfectly controlled. I use 3 in different grow tents. It’s nice to see from your phone how your tent temps are. Does High and Low and records data.*

It would be helpful if you bookmarked it, so people don't need to listen to all the unnecessary 4 minutes at the beginning. That said, for anyone who's interested, the important part begins at 4:16

Dumb didn’t help

Very helpful. Thanks.

Thanks for the detail. It's really help for beginner like me. And I'm really tired for the cement drilling.

Mine is still in service, it was installed about 1955.

Yes, but does it work? Folks want to see it WORK.

Fascinating! What's the resistance of the rheostat? I've experimented with shorting the terminals and got about 300mA. I'm guessing the rheostat also serves as a protective resistor in case of a short?..

16D double headed nail with forming wire over ramset or tapcon.

Really liked this video.... 2 wires going to it?

dadjob

mom job

I've been trying to figure out the same thing with my SR504 & 2 Nest thermostats. Your videos and explanation are so helpful!! Did you have to upsize the wire from #18 while combining all C wires? I'm guessing the amperage limit should be fine as these draw low current?